HTBLF-1700 Small chamber furnace is a compact bottom loading furnace driven by an electric motor that is used for rapid heating and rapid cooling small sample in the air up to 1700ºC. The furnace also can be used for cycling thermal impact test.
Furnace Features | Two-layer casing with air cooling. The inner is made of alumina polycrystalline fiber. Coated with high-temperature alumina to improve the reflectivity, the heating efficiency, and its service life. The bottom loading mechanism is built-in, which is driven by a DC motor for fast heating samples into the pre-heated chamber. |
Power | 208 - 240 VAC, 50/60 Hz, single phase Max. Power: 2.5 kW Power cable is included, but no plug |
Working Temperature | 1600 °C, continuously 1700 °C, < 30 minutes |
Heating Chamber | L100 × W100 × H150 mm with 4 pieces of U-type MoSi2 heating element One 30 mm diameter hole is open on the bottom of the heating chamber One fibrous alumina rod is installed to insert an alumina crucible into the chamber via a lifting fixture |
Heating Rate | 10℃/min (room temperature —1400℃) 5℃/min (1400℃-1600℃) 2℃/min (>1600℃) |
Thermocouple | Type B |
Temperature Control | FA-YD518P-AG temperature controller is included. Proportional–integral–derivative control (PID control) and auto-tune function 30 segments programmed with ramping, cooling and dwelling steps Built-in over-temperature alarm and thermocouple failure alarm +/- 1 ºC temperature control accuracy Default DB9 PC communication port |
Overall Dimension | L540 x W 500 x H 1000 (mm) |
Net Weight | 70 KG |
Warranty | One-year limited warranty (Consumable parts such as heating elements, processing tubes, the crucible, and O-rings are not covered by the warranty, please order the replacement at related products below. Damage caused by the use of corrosive and acidic gases is not covered by the warranty. |
HTBLF-1700 Small chamber furnace is a compact bottom loading furnace driven by an electric motor that is used for rapid heating and rapid cooling small sample in the air up to 1700ºC. The furnace also can be used for cycling thermal impact test.
Furnace Features | Two-layer casing with air cooling. The inner is made of alumina polycrystalline fiber. Coated with high-temperature alumina to improve the reflectivity, the heating efficiency, and its service life. The bottom loading mechanism is built-in, which is driven by a DC motor for fast heating samples into the pre-heated chamber. |
Power | 208 - 240 VAC, 50/60 Hz, single phase Max. Power: 2.5 kW Power cable is included, but no plug |
Working Temperature | 1600 °C, continuously 1700 °C, < 30 minutes |
Heating Chamber | L100 × W100 × H150 mm with 4 pieces of U-type MoSi2 heating element One 30 mm diameter hole is open on the bottom of the heating chamber One fibrous alumina rod is installed to insert an alumina crucible into the chamber via a lifting fixture |
Heating Rate | 10℃/min (room temperature —1400℃) 5℃/min (1400℃-1600℃) 2℃/min (>1600℃) |
Thermocouple | Type B |
Temperature Control | FA-YD518P-AG temperature controller is included. Proportional–integral–derivative control (PID control) and auto-tune function 30 segments programmed with ramping, cooling and dwelling steps Built-in over-temperature alarm and thermocouple failure alarm +/- 1 ºC temperature control accuracy Default DB9 PC communication port |
Overall Dimension | L540 x W 500 x H 1000 (mm) |
Net Weight | 70 KG |
Warranty | One-year limited warranty (Consumable parts such as heating elements, processing tubes, the crucible, and O-rings are not covered by the warranty, please order the replacement at related products below. Damage caused by the use of corrosive and acidic gases is not covered by the warranty. |
