HTTF-1200-S Sliding Tube Furnace is a single-temperature zone rapid thermal processing electric sliding furnace. This electric furnace has a maximum heating rate of 10℃/min and is equipped with a sliding rail at the bottom, which allows the furnace to slide from one side of the tube to the other for rapid heating and cooling. This RTP furnace can also be used for the CVD growth of graphene and carbon nanotubes.
HTTF-1200-S Sliding Tube Furnace is a single-temperature zone rapid thermal processing electric sliding furnace. This electric furnace has a maximum heating rate of 10℃/min and is equipped with a sliding rail at the bottom, which allows the furnace to slide from one side of the tube to the other for rapid heating and cooling. This RTP furnace can also be used for the CVD growth of graphene and carbon nanotubes. It uses a touch screen and PLC control, which allows for adjustable speed.
Power | AC 208-240V Single Phase, 50/60 Hz 3 kW |
Heating | Maximum:1200℃< 0.5 hrs Continuous Working: 1100℃ or less Recommended heating rate ≤10℃/min Heating zone length: 400mm |
Thermocouple | K-type |
Specs | Slide distance: 400mm (can be customized at extra cost) Adjustable speed range: 10-100mm/s (can be customized at extra cost) and can also be set to move back and forth The heating will automatically slide to the far right from the far left according to the temperature program after reaching a certain temperature The maximum heating rate for the left sample area: 3℃/s Rapid cooling rate for samples inside the furnace: 3℃/s (500-100℃), 0.7℃/s (500-200℃) |
Temperature Controller | Two PID automatic controllers with 50 programmable segments for control of heating & cooling rate, and dwell time. Built-in overheating & thermocouple broken protection. +/- 1 ºC temperature accuracy. DB9 PC Communications Port. PC Control: A laptop PC can be ordered for $500 together with the furnace. We recommend ordering a computer (laptop) from us to avoid software installation problems as we will perform installation and testing before shipping. |
Vacuum Flanges | One set of stainless steel sealed flanges The flanges and quartz tube are sealed with O-rings, pressure rings, and O-rings, and tightened by threaded compression to ensure sealing The left flange has a KF25 vacuum interface, needle valve, and barb venting port The right flange has a needle valve, G1/4 air inlet, and mechanical pressure gauge. |
Quartz Tube Options | 25 O.D x 19 I.D x 1400 L (mm) 50 O.D x 44 I.D x 1400 L (mm) 60 O.D x 55 I.D x 1400 L (mm) 80 O.D x 75 I.D x 1400 L (mm) 100 O.D x 95 I.D x 1400 L (mm) |
Vacuum Level | Limited by a vacuum pump 10^-2 torr can be achieved by a mechanical pump 10^-5 torr can be reached by a molecular pump The vacuum pump is not included, please order separately |
Dimensions | 1900 * 500 * 680mm |
Net Weight | ~ 210 Kg |
Warranty | One-year limited manufacturer's warranty (Consumable parts such as processing tubes, o-rings and heating elements are not covered by the warranty, please order replacements at related products below). |
Application Notes | Tube furnaces with quartz tubes are designed for use under vacuum and low pressure < 0.12 MPa Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation. Vacuum pressures may only be safely used up to 1000°C |
HTTF-1200-S Sliding Tube Furnace is a single-temperature zone rapid thermal processing electric sliding furnace. This electric furnace has a maximum heating rate of 10℃/min and is equipped with a sliding rail at the bottom, which allows the furnace to slide from one side of the tube to the other for rapid heating and cooling. This RTP furnace can also be used for the CVD growth of graphene and carbon nanotubes. It uses a touch screen and PLC control, which allows for adjustable speed.
Power | AC 208-240V Single Phase, 50/60 Hz 3 kW |
Heating | Maximum:1200℃< 0.5 hrs Continuous Working: 1100℃ or less Recommended heating rate ≤10℃/min Heating zone length: 400mm |
Thermocouple | K-type |
Specs | Slide distance: 400mm (can be customized at extra cost) Adjustable speed range: 10-100mm/s (can be customized at extra cost) and can also be set to move back and forth The heating will automatically slide to the far right from the far left according to the temperature program after reaching a certain temperature The maximum heating rate for the left sample area: 3℃/s Rapid cooling rate for samples inside the furnace: 3℃/s (500-100℃), 0.7℃/s (500-200℃) |
Temperature Controller | Two PID automatic controllers with 50 programmable segments for control of heating & cooling rate, and dwell time. Built-in overheating & thermocouple broken protection. +/- 1 ºC temperature accuracy. DB9 PC Communications Port. PC Control: A laptop PC can be ordered for $500 together with the furnace. We recommend ordering a computer (laptop) from us to avoid software installation problems as we will perform installation and testing before shipping. |
Vacuum Flanges | One set of stainless steel sealed flanges The flanges and quartz tube are sealed with O-rings, pressure rings, and O-rings, and tightened by threaded compression to ensure sealing The left flange has a KF25 vacuum interface, needle valve, and barb venting port The right flange has a needle valve, G1/4 air inlet, and mechanical pressure gauge. |
Quartz Tube Options | 25 O.D x 19 I.D x 1400 L (mm) 50 O.D x 44 I.D x 1400 L (mm) 60 O.D x 55 I.D x 1400 L (mm) 80 O.D x 75 I.D x 1400 L (mm) 100 O.D x 95 I.D x 1400 L (mm) |
Vacuum Level | Limited by a vacuum pump 10^-2 torr can be achieved by a mechanical pump 10^-5 torr can be reached by a molecular pump The vacuum pump is not included, please order separately |
Dimensions | 1900 * 500 * 680mm |
Net Weight | ~ 210 Kg |
Warranty | One-year limited manufacturer's warranty (Consumable parts such as processing tubes, o-rings and heating elements are not covered by the warranty, please order replacements at related products below). |
Application Notes | Tube furnaces with quartz tubes are designed for use under vacuum and low pressure < 0.12 MPa Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation. Vacuum pressures may only be safely used up to 1000°C |
